As an Amazon Associate I earn from qualifying purchases.
1. Accrie #ad
Accrie USB Downloader Jtag ISP Programmer ispDownload Cable Lattice FPGA CPLD HW-USBN-2 #adAccrie #ad
- Support all lattice fpga and cpld sc/scm/xp/xp2/ec/ecp2/ecp2m/machxo/machxo2/1000/2000/4000/ECP3. Support diamond, isplever, lattice programmer. Automatically senses and adapts to target i/o voltage.
Support for jtag, internal FLASH, spi flash programming mode, etc. Interfaces to devices operating at 5VTTL, 3VLVCMOS, 2. 5v, 1. 8v and 1. 5v. Support win 2k, win xp, win8, win7, win10 and other operating systems.
2. Fauge #ad
Fauge USB Isp Download Cable JTAG SPI Programmer for Lattice FPGA CPLD HW-USBN-2 #adFauge #ad
- Type: drive IC. Operating temperature: -10-40 Celsius. Supply voltage: 5V. Condition: New. Model number:for lattice ispDOWNLOAD Cables.
3. Andifany #ad
Andifany USB Isp Download Cable JTAG SPI Programmer for Lattice FPGA CPLD HW-USBN-2 #adAndifany #ad
- Condition: New. Operating temperature: -10-40 Celsius. Type: drive IC. Supply voltage: 5V. Model number:for lattice ispDOWNLOAD Cables.
4. XYG-AVR #ad
Atmel-ICE Basic Kit AVR SAM Programmer Debugger Supports JTAG SWD PDI TPI aWire SPI debugWIRE with Additional Adapter and [email protected] #adXYG-AVR #ad
- Supports all built-in hardware breakpoints in the target microcontroller number depends on the OCD module in the target. Supports jtag, swd, tpi, pdi, awire, SPI and debugWIRE interfaces.
Powerful development tool for debugging and programming Atmel SAM and AVR microcontrollers, Comes with additional adapter and cables. Full source-level debugging in Atmel Studio. Atmel-ice Basic Kit.
5. Waveshare-AVR #ad
Waveshare ATMEL AVR Programmer USB AVRISP XPII Compatible Atmel at AVR ISP mk2 mkII in-System Programmer Supports AVR Studio 4/5/6/7 Or Higher Version #adWaveshare-AVR #ad
- Upgradable to support future Devices Adjustable ISP programming speed up to 8M frequency. Usb 2. 0 compliant full speed, 12mbps 3 optional cables to target board Powered from USB bus, does not require external power supply.
Supports avr studio 4/5/6 or higher version delivered with Firmware For AVR Studio 5, Can Be Updated To Support Other AVR Studio Versions. Supports fuses and lock bit Programming Based on AT AVRISP mkII firmware. Supports all avr devices with isp or pdi interface, and certain 51 Devices Programs both Flash and EEPROM.
|Part Number||USB AVRISP XPII|
|Model||USB AVRISP XPII|
6. ELEGOO #ad
40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit Compatible with Arduino Projects, ELEGOO 120pcs Multicolored Dupont Wire 40pin Male to Female #adELEGOO #ad
- The cables can be separated to form an assembly containing the number of wires you require for your connection and to support non-standard odd-spaced headers. We have always cared about the customer experience and improve the product function details.
Each cable length: about 20 cm /8-inch. Packing in a color box. Including 1x 40-pin male to female jumper wires, 1X 40-pin male to male jumper wires, 1x40-pin female to female jumper wires.
7. HiLetgo #ad
HiLetgo FT232RL FTDI Mini USB to TTL Serial Converter Adapter Module 3.3V 5.5V FT232R Breakout FT232RL USB to Serial Mini USB to TTL Adapter Board for Arduino #adHiLetgo #ad
- Support win95/98/98se/me/2000/xp/win7 32bit 64bit /Vsita/, do not Support Win8. Rxd/txd transceiver communication indicator, with 500MA self-restore Fuse. Chipset: ft232rl, not genuine ftdi chip, Working Voltage: 3. 3v/5. 5v. Pin definition: dtr, rxd, VCC, cts, tx, GND.
8. KOOBOOK #ad
KOOBOOK 1Set USBTiny USBtinyISP AVR ISP Programmer for Arduino Bootloader USB Download Interface #adKOOBOOK #ad
- It can be used to download programs for most AVR microcontrollers. The arduino ide is always compatible with the USBtinyISP download line, which is mainly used to download the bootloader.
Usb power supply, after choosing the bord need to download the hardware name, start downloading bootlaoder, in the burn bootloader choose usbtinyisp, open the Arduino IDE, can provide direct power to the Arduino, then download is completed within 1-2 minutes.
Usbtinyisp is an isp line download based on usb interface designed for avr microcontrollers. Isp connector: 6-pin and 10-pin, size: 28.
8mm × 61. 6mm. Power supply options: external power supply and USB power supply if using an external power supply chip set ISP10 near yellow jumper cap removed. The download cable to connect the supplied 6 pin connector, can be used as an addition to the Arduino download cable, but also suitable for downloading most of the AVR program.
9. Geekstory #ad
For ATMEL 51 AVR USB ISP ASP Microcontroller Programmer Downloader with Cable + 10Pin to 6Pin Adapter Board for Ender 3 or Ender 3 Pro Geekstory #adGeekstory #ad
- Reserved mosi, gnd. With power and programming two lights, the asp is the new version, the target board suopports 5V and 3. 3v power supply new self-adaptive automatic speed control, with pin on JP2.
Set programming programming interface, the user can upgrade the downloader firmware, programming is very convenient. This usbasp programmer is using onboard atmega8 chip. Driver installation is required to start the usb to isp.
This usbasp programmer only supports windows system. It can be directly connected to the USB interface of the computer, which is very convenient to use. This product can be used to update Ender 3 or Ender 3 Pro firmware.
If you need technical documentation, in the new page, please click “Geekstory”you can find "Sold by Geekstory" under Buy Now button, click “Ask a question” to email us. 6pin interface, miso, ret, sck, VCC, user-friendly connection to the target board. The avr usb isp asp microcontroller documentation link cannot be displayed.
10. SENMOD #ad
A Set AVR ISP USBtinyISP Programmer for Arduino Bootloader USB Download Interface #adSENMOD #ad
- Size: 28. 8mm × 61. 6mm. Isp connector: 6-pin and 10-pin. The download cable to connect the supplied 6 pin connector, can be used as an addition to the download cable for Arduino, but also suitable for downloading most of the AVR program.
Power supply options: external power supply and USB power supply if using an external power supply chip set ISP10 near yellow jumper cap removed.
For the arduino, after choosing the bord need to download the hardware name, in the Burn Bootloader choose USBtinyISP, open the IDE, which can provide direct power to, start downloading bootlaoder, USB power supply, then download is completed within 1-2 minutes.